Forums-viewtopic-Звезда обновилась «Поле боя»

Была похожая тема по акрилу..
Вот нашел инфу - м.б. кому-то пригодится (сам крашу акрилом)

've used this technique with old models and figures, even those that have been covered in two or three coats of thick enamel paint. It works equally as well with hard and soft plastic plus it's a technique that's not just limited to smallscale modelling.

You'll need the following items :

* Household oven cleaner
* Plastic gloves
* Plastic bag
* Plastic bucket.
* Toothbrush
* Detergent (washing-up liquid)

Houshold oven cleaner in a spray-can form is cheap and readily available in practically any supermarket. It's used to dissolve thick carbon and burned fat deposits from off the inside ovens and off frying pans. Luckily for us modellers it also dissolves enamel paints without affecting plastic.

Procedure

In this example we'll use a couple of old soft-plastic polythene figures. They're all in good condition, but have been painted with thick blobs of enamel paint.

A word of warning - oven cleaner is caustic and may cause burns to the skin or eyes or respiratory problems if not used correctly. I would stress that it be used with caution. Minors should never use these products themselves, they should ask a responsible adult to do it for them.

* Start by laying out the plastic bag on a flat surface and place the model or figures onto the bag.

* Put on your gloves. Make sure you use plastic gloves to protect your hands as oven cleaner can burn the skin. Don't use latex gloves as the oven cleaner may dissolve the latex.

* Hold the oven cleaner spray in one hand, and spray the model liberally. With the other hand you can turn over the model while holding it over the plastic bag so as to get into every nook and cranny.

* Close the plastic bag with the model inside and tie a knot, place into the plastic bucket and leave overnight. The plastic bucket is so that if any oven cleaner leaks out it will not stain the floor.

* Rinse any over cleaner off your gloves and put them away and leave over cleaner to work overnight.

* 24hrs later, get out your plastic gloves again and take the bucket to somewhere you have access to a cold water tap and a sink.

* Put on your gloves, take the model out the plastic bag - you'll find a huge gooey mess, but don't despair). Throw the plastic bag away and put the model into the sink.

* Turn on the cold water and you'll find the paint will fall off as you rinse it. Now with the toothbrush and with a little detergent you can remove any stubborn remnants of paint stuck in little nooks and crannies.

* Give them a final rinse and leave to dry. Rise your gloves and don't forget to clean out the bucket or container.

* One dry that's it, finished. Shiny "new" figures , ready for painting !

А мои в ацетоне прекрасно искупались.
Хорошо что Звезда из полиэтилена фигурки делает. Wink

ацетон(растворитель) + та самая зубная щетка

но по мне - если на фигурках и так акрил, то для новой покраски проще из баллона загрунтовать поверху Smile

SAXON, а можешь краткий перевод дать? буду очень признателен. так как сам сейчас столкнулся с этой проблемой.

я вот АКАНовскую эмаль снимал с помощью жидкости для прочистки труб "Крот". эмаль то слезла а АКАНовская грунтовка осталась. посоветуйте как ее снять без вреда для пластика

сидол я не нашел. но купил жидкость для чистки духовки "шуманит" за 170 руб. результатом доволен. насыпал в баночку миньки, залил жидкостью. и через сутки эмаль сошла без труда.

кстати, а алкониты (вроде так называется) как взаимодействуют со звездовским клеем?

		Архивы сайта \| Наши форумы \| Поиск \| "Последнее на форуме"

"Поле боя" \| Каталог файлов \| Каталог ссылок \| Управление профилем